The buoyancy of the fishing float is required to be greater than the gravity of the fishing bait and the lead sinker to ensure that the float is exposed to the water. When the adjustment is close to and less than this standard, it will do.
The sea pole wheel must be adjusted to release the force When the fish bites the hook and lifts the bar, when the tension between the fish and the fish is greater than the limit value of the tension of the line, the line will be cut. The diameter of the line is 0.3 is sufficient. sea pole fishing float When using a sea rod, a lead sinker is very important. Because of the long movement distance from the plumb bottom to the float on the water surface, and then to the underwater fishing group, the sensitivity is low. I tried and found the following problems. According to different waters, I choose fishing rods of different lengths.
It is suitable for bad food on the bottom of mud, sand and gravel, and other relatively flat water bottoms. To Sea pole fishing bottom When fishing in a new water area, it is best for the fishermen of the fishing club to understand the underwater situation, especially the fishing reservoir. A thread of about 0. After the fish has eaten, the lead sinker must be driven when lifting the rod before the hook can move.
The wind is too strong. Everyone has the experience when using the sea pole, and the fish will not be caught until the predetermined fishing position is reached. To adjust the wheel’s release force, according to the different diameters of the wire, first take a good look at the nodule tension of the wire, and then assemble the sea pole, connect a spring scale to the nodule of the main wire, and pull it outward. It is cheap and eye-catching. Don’t pull it too tight, but relax it.
The wire is too hard. Now I will mainly explain the method of fishing float. Fly hooks, mushroom food, try to use unloved bait. This method has high sensitivity, and the hook is moved when the rod is lifted, but it will shift when the wind blows. Use this as a standard to adjust the venting force. In other words, it is necessary to minimize the impact of wind on fishing lines and rods. For the sea pole without back cover, pull out three-quarters of each section and place it in a ventilated place to dry or sun dry, so that the water will evaporate from the gap between the two sections. You must first understand the underwater situation before you can go down, otherwise you will lose a lot.
Some fishing lines are originally unqualified products. Without a lead sinker, the hook can quickly leave the bottom, thus avoiding the hook. For fish of the same weight, the thread used for the hand pole should be thicker than that used for the sea pole. It will inevitably affect the distance you hit and make the hook fall closer. The amount of activity on the line is 150 mm. When the venting force is close to and less than the nodule tension and is pulled out, the venting force is adjusted. Remove the pole and replace it with new food, preferably pasta, and re-enter the fishing position.
https://www.yongmiao.com/product/fishing-swivel/
The sea pole wheel must be adjusted to release the force When the fish bites the hook and lifts the bar, when the tension between the fish and the fish is greater than the limit value of the tension of the line, the line will be cut. The diameter of the line is 0.3 is sufficient. sea pole fishing float When using a sea rod, a lead sinker is very important. Because of the long movement distance from the plumb bottom to the float on the water surface, and then to the underwater fishing group, the sensitivity is low. I tried and found the following problems. According to different waters, I choose fishing rods of different lengths.
It is suitable for bad food on the bottom of mud, sand and gravel, and other relatively flat water bottoms. To Sea pole fishing bottom When fishing in a new water area, it is best for the fishermen of the fishing club to understand the underwater situation, especially the fishing reservoir. A thread of about 0. After the fish has eaten, the lead sinker must be driven when lifting the rod before the hook can move.
The wind is too strong. Everyone has the experience when using the sea pole, and the fish will not be caught until the predetermined fishing position is reached. To adjust the wheel’s release force, according to the different diameters of the wire, first take a good look at the nodule tension of the wire, and then assemble the sea pole, connect a spring scale to the nodule of the main wire, and pull it outward. It is cheap and eye-catching. Don’t pull it too tight, but relax it.
The wire is too hard. Now I will mainly explain the method of fishing float. Fly hooks, mushroom food, try to use unloved bait. This method has high sensitivity, and the hook is moved when the rod is lifted, but it will shift when the wind blows. Use this as a standard to adjust the venting force. In other words, it is necessary to minimize the impact of wind on fishing lines and rods. For the sea pole without back cover, pull out three-quarters of each section and place it in a ventilated place to dry or sun dry, so that the water will evaporate from the gap between the two sections. You must first understand the underwater situation before you can go down, otherwise you will lose a lot.
Some fishing lines are originally unqualified products. Without a lead sinker, the hook can quickly leave the bottom, thus avoiding the hook. For fish of the same weight, the thread used for the hand pole should be thicker than that used for the sea pole. It will inevitably affect the distance you hit and make the hook fall closer. The amount of activity on the line is 150 mm. When the venting force is close to and less than the nodule tension and is pulled out, the venting force is adjusted. Remove the pole and replace it with new food, preferably pasta, and re-enter the fishing position.
https://www.yongmiao.com/product/fishing-swivel/
コメント